Emtec Electronic attends the Corrugated Week in Indianapolis, USA
For the first time, emtec Electronic GmbH will attend the Corrugated Week in Indianapolis, USA from September 24th to 27th 2018, together with its US representative Technidyne Corporation. At exhibition booth no. 848 the company will present innovative testing instruments for the corrugated board industry.
The special EST12 Surface & Sizing Tester determines those surface parameters of paper and board, which are relevant for the converting process, in particular the surface sizing / hydrophobicity and surface porosity. With its help, converting properties, such as printability, gluability, coatability and dusting tendency can be predicted. It enables the optimal runnability during the finishing or converting process of paper/board. An according modular system PDA.C02 Penetration Dynamics Analyzer for more applications is available.
Alongside with the EST12, emtec will have the CAS touch! and FPA touch! on display. These instruments represent the most-modern charge measuring systems for the wet-end in paper and board production and are used to measure the interaction between particles or fibers with additives and process chemicals in the pulp suspension. The use of both instruments in the production process helps to optimize the utilization of chemicals with the objective to stabilize the process, to improve the product quality and to reduce cost.
The new measuring method to measure the mineral filler content of the ACA Ash Content Analyzer, is nondestructive, quick, easy and accurate. Typical mineral filler and pigment content in paper and board, such as calcium carbonate, kaolin/ talcum, titanium dioxide, and the total mineral filler content in percent are determined. It enables optimal process control due to instant availability of measuring results, and helps to narrow down the specifications for the filler content in the finished product and therefore to optimize the consumption of fillers.
Additionally, emtec Electronic will inform about its DSS Dimension Stability System, a modular measuring system for the investigation of the dimension stability of paper, board and foils in one-sided contact with temperature or liquids. The WSD module Wet Stretch Dynamics Analyzer measures the dynamics of the change in dimension of paper under one- sided liquid contact. And the HSA module Heat Shrinkage Analyzer predicts the dimension stability of paper, board and foils in contact with high temperature during the converting process.
Just like two years ago, Emtec will attend the Tissue World Trade Show and Conference to be held at Istanbul Congress Center in September 2018. The German producer of innovative laboratory and online testing machines will be based on floor B5 at booth no. D171 together with its Turkish representative LABTEK.
Centerpiece of the booth will be the well-known TSA – Tissue Softness Analyzer which is used to reliably assess the Softness, Smoothness/Roughness and Stiffness as well as the overall Hand Feel of tissue and nonwoven materials.
Alongside with the TSA, Emtec will have the CAS touch! and FPA touch! on display. These instruments represent the most-modern charge measuring systems for the wet-end in tissue and paper production and are used to measure the interaction between particles or fibers with additives and process chemicals in the pulp suspension. The use of both instruments in the production process helps to optimize the utilization of chemicals with the objective to stabilize the process, to improve the product quality and to reduce cost.
Special testing solutions for product and process optimization as well as cost savings
Emtec Electronic shows its novelties and known testing models for the wet and dry part of paper, board and tissue production at the PaperCon 2017
The measuring device manufacturer emtec Electronic will also participate at this years’ PaperCon 2017 from April 23 – 26, 2017 in Minneapolis, Minnesota, USA. The German company can be found at the Technidyne booth, which is the US sales partner of emtec (booth no. 611).
Paper, board and tissue – starting from the pulp until the final product – it can all be measured with the special measuring devices by emtec:
In the wet end, the new AFG touch! units can help to optimize the dosage of chemicals and stabilize the production process, and thereby, the final product. In particular, the new FPA touch! Fiber Potential Analyzer and CAS touch! Charge Analyzing System for measurement of the zeta potential of fibers and the particle charge in pulp suspensions are first time introductions to the visitors of the PaperCon.
Everyone, who is interested in the softness of its tissue products, has surely already heard of emtec Electronic and its TSA Tissue Softness Analyzer to determine the three single parameters of the softness (Real Softness, Smoothness, Stiffness) and the automatically computed Hand Feel value.
When issues with glueability, printability and coatability occur in the converting of paper and board, and no one knows where they come from, the EST12 Surface & Sizing Tester or the modular system PDA.C02 Penetration Dynamics Analyzer can help to solve these issues by the determination of the surface parameters – surface sizing and surface porosity. These are of real importance for the converting process.
We are happy to welcome you at our booth in order to discuss the innovative testing solutions, developed and manufactured by emtec, in more detail. All mentioned devices will be at the booth and it will also be possible to measure samples and to discuss the results.
emtec Electronic at the Zellcheming Expo in Germany
emtec Electronic GmbH will attend the “Zellcheming Expo 2016” in Frankfurt/Main, Germany
– celebrating the 20th anniversary and 20th exhibition participation. From June 28th until 30th, emtec will be present at the exhibition booth no. 11.0 - C48.
During the Zellcheming Expo, emtec will show a variety of testing instruments by which the complete production process can be controlled and guided in the right direction, to get an efficient process and the best possible quality with the lowest possible costs.
In the wet end it is extremely important to have detailed information about the charges of particles in the pulp suspension, which can be determined by the CAS Charge Analyzing System. The latest version of this equipment is the smallest and lightest than ever! Beside this, the knowledge about the surface charge of the pulp fibers, which can be measured with the lab equipment FPA Fiber Potential Analyzer is also important.
With the innovative ACA Ash Content Analyzer it is possible to determine the total mineral filler content as well as the percentage content of the typical fillers of the paper within seconds. The PDA.C02 Penetration Dynamics Analayzer delivers reliable predictions about the behavior of paper surfaces during glueing, printing and coating processes. The TSA Tissue Softness Analyzer measures objectively the softness and calculates the handfeel of tissue
Innovative Tools to Optimize Production and Converting Processes
emtec Electronic looks back to a successful exhibition week at the RosUpack 2015
The company emtec Electronic GmbH attended the Russian „RosUpack 2015“ in June in Moscow. In the red emtec corner in hall 2 of the exhibition, visitors were able to talk to specialists from emtec in Germany and from the representative company Sigma Micron in Russia. In particular, producers and converters of paper and board as well as suppliers of chemicals, glue, coating color, printing ink, but also institutes can indeed be very well supported by the emtec measuring instruments.
In the converting process of paper and board sometimes problems occur in the gluing, coating and printing process, but the reason is unclear, as the specifications are according to standard testing instruments. Nobody knows if it is due to the quality of the paper or the glue, coating color or printing ink.
The company emtec developed a method to find out the reason. In Moscow one of the solutions was presented - the EST12 Surface & Sizing Tester. In order to predict the interaction between paper or board and the liquid during coating, printing and gluing, the device characterizes the surface parameters of paper and board, which are relevant for the converting process, in the process-relevant time. Its application leads to the optimization of the production and converting processes and therefore to reducing the costs and achieving respectively improving the quality of the product.
Problems in the quality of the finished product can also be caused by non-optimal process control in the wet end area of paper and board production. emtec Electronic has presented two essential measuring devices for the optimization of wet end area: the CAS Charge Analyzing System for determining the particle charge and the FPA Fiber Potential Analyzer for measuring the Zeta Potential of fibers in the suspension. Both help to guarantee and improve the targeted properties of finished products and to reduce the consumption of chemicals.
Process Optimization within the Paper, Board and Tissue Production
On May 20th and 21st, emtec Electronic GmbH will participate at the “Future. Forum Paper” – the Austrian Paper Conference with trade show for pulp and paper industry in Graz.
During the two days emtec will present different testing instruments by which the process from the production of the pulp to the conversion to the finished product can be controlled and guided in the right direction to get an efficient process and the best possible quality with the lowest possible costs.
In the wet end it is extremely important to have detailed information about the charges of particles in the pulp suspension, which can be determined by the CAS Charge Analyzing System. Also important is the knowledge about the surface charge of the pulp fibers, which can be measured with the FPA Fiber Potential Analyzer. Furthermore, emtec Electronic developed a new Online measuring device FPO Fiber Zeta Potential Analyzer Online, which measures the Zeta Potential of fibers directly in the process and delivers reliable and necessary information concerning the efficiency of chemicals in the process immediately.
In addition to the wet end, it is necessary to get an idea of the quality of the base paper after the production and of the finished product after converting. The EST12 Surface & Sizing Tester is one of the equipment for determining important paper surface properties such as hydrophoby and sizing as well as the porosity and pore structure, which have influences on the printability, coatability, and glueability.
Especially for tissue and nonwoven products, the TSA Tissue Softness Analyzer gives reliable and objective information about the real softness, smoothness/roughness, stiffness as well as the final hand feeling.
Another innovative device is one of the latest developments: the ACA Ash Content Analyzer. It allows the fast and accurate determination of the total mineral filler content as well as the percentage content of the individual filler components of paper and board. It is a useful alternative to the traditional combustion method.
Softness Evaluation: An Introduction to the Nonwoven-Market
emtec Electronic at the ANEX & SINCE 2015 in Shanghai, China
The company emtec Electronic will participate at the “ANEX & SINCE 2015” in Shanghai, China from 13th to 15th of May. The event will be a combination of the Asia Nonwovens Exhibition and Conference (ANEX) and the Shanghai International Nonwovens Conference and Exhibition (SINCE). The company emtec will be present at booth no. V21 together with Shanghai Forest & Paper Scientific Instrument – its representative for China.
At the exhibition booth emtec will present its TSA – Tissue Softness Analyzer, which was developed for the tissue industry, but is also applicable in the nonwoven sector. The device allows the optimization of the production and converting process, the quality control from supplied products, and also the quality assurance during the production and converting process. Furthermore, the TSA can be used in the R&D to develop new products and to improve existing products.
The TSA – Tissue Softness Analyzer gives reliable and objective information about the real softness, smoothness/ roughness, stiffness as well as the final hand feeling. The availability of these three parameters opens a huge amount of chances for the optimization of the production and converting processes.
More information about the device and its application will be given by Mr. Alexander Gruener in his presentation “TSA: A new method for Process Optimization, QA and R&D in Nonwovens Production and Converting.” on Wednesday, 13th May at 10:05 am.
When Standard Methods like Cobb or Bendtsen come to their Limit
emtec Electronic and their EST12 – Surface & Sizing Tester at PaperCon 2015
This year emtec Electronic will be present at the PaperCon 2015 Exhbition and Conference with their EST12 – Surface & Sizing Tester. The company itself will have a presentation on Tuesday, 21st April at 1:14 pm. Additionally, the company Technidyne Corporation – the representative in the USA – will be present from 19th to 22nd April in Hall 2 at their booth no. 325.
The Cobb or Bendtsen tests are used to get an information about the sizing and the pore structure of paper, especially to check the quality and the processability of the paper in the converting. But it happens, that the results are the same, but one paper works and the other does not. How and why this happens will be explained by Alexander Gruener during his presentation “emtec EST12 – Surface & Sizing Tester. Where standard methods like Cobb or Bendtsen come to their limit.” He also will explain in detail the function of the emtec device EST12 and how it makes it possible to predict reliably the behavior of paper surfaces during converting processes like glueing, coating and printing by giving more detailed information about the surface sizing respectively hydrophoby, and the surface pore structure of paper and board.
With the application of the special testing equipment from emtec Electronic it is possible to control and guide the production and converting process into the right direction, in order to get an efficient process and the best possible quality with the lowest possible cost.
Gaining the Best Tissue Quality with Lowest Possible Costs
This year the first Tissue World exhibition will take place in Sao Paulo, Brazil and the company emtec Electronic will attend this event from May 20th until 22nd at booth no. 383. The company will present their technical measurement equipment to South and Latin American visitors together with their representative Elof Hansson Ltda. in Brazil.
The TSA Tissue Softness Analyzer is one of the innovative testing instruments which will be presented in Sao Paulo during these three days of exhibition. The device is used for the objective and reliable measurement of tissue “handfeel” properties such as the real softness, smoothness/roughness and stiffness. The availability of these three parameters opens a huge amount of chances for the optimization of the tissue production and converting processes.
Additionally, emtec Electronic will present their measuring devices for the wet end area: the CAS Charge Analyzing System for determining the particle charge of filtrates, the FPA Fiber Potential Analyzer for measuring the Zeta Potential of fibers in the pulp, and the DFA Dynamic Filtration Analyzer for simulating the drainage and retention processes of the pulp during the production.
High Paper Quality by Application of Quality Equipment
This year the “Asian Paper 2015” will take place in Jakarta, Indonesia and the company emtec Electronic GmbH will attend. From April 28th until 30th, the company will present different paper testing equipment at booth no. C27.
In the wet end of the paper production process it is extremely important to have detailed information about the charges of particles in the pulp suspension, which can be determined by CAS Charge Analyzing System. Also important is the knowledge about the surface charge of the pulp fibers, which can be measured with the FPA Fiber Potential Analyzer. Furthermore, emtec Electronic developed a new Online measuring device FPO Fiber Zeta Potential Analyzer Online, which measures the Zeta Potential of fibers directly in the production process.
In addition to the wet-end, it is necessary to get information about the quality of the base and final products. Therefore emtec will present the EST12 Surface & Sizing Tester in Jakarta, which characterizes the process relevant surface parametersof paper and board in order to predict its converting properties. Additionally, the TSA Tissue Softness Analyzer will be shown, which gives reliable and objective information about the “hand feel” and different softness parameters of tissue products.
In summary, the application of all these measuring devices leads to the optimization of the production and converting processes to gain the best possible quality at the lowest possible costs.